Commonplace
Sell an itemMy account
Home/Blog/Scooters and mopeds/How to Move or Take Apart a Moped: Truck, Trailer, 7 Tie-Down Steps
Scooters and mopeds

How to Move or Take Apart a Moped: Truck, Trailer, 7 Tie-Down Steps

How to move a moped: the ramp, chock and straps you need, what to remove, a 7-step tie-down, protecting the bodywork, and what moped shipping costs.

Commonplace
Research
November 20, 2026 · 14 min read
More guides →

Here's how to move a moped: roll it up a ramp into a pickup, van or utility trailer with two people, stand it upright against a wheel chock, and hold it with four tie-down straps anchored to solid frame points (never plastic body panels). Most 50cc mopeds and scooters don't need to be taken apart at all; at most you pull the mirrors and top box. If you'd rather ship it, uShip's own figures put average moped shipping at about $0.51 per mile for trips under 1,000 miles, and about $2.30 per mile for short hauls under 100 miles.

I help people buy and sell bikes, scooters and other things with wheels for a living, and mopeds are deceptively easy to damage in a move. They're light enough that people get casual, and the bodywork is thin plastic that cracks the moment a strap pulls on it. So this guide covers whether you can do it yourself, the gear, what comes off, the step-by-step load and tie-down, protecting the moped and your vehicle, what shipping costs, and what to check when it comes off the truck. If you're moving it because you're selling it, my guide on how to sell a used moped covers the rest.

Can you move a moped yourself?

Yes, a moped is one of the easier vehicles to move yourself. With a ramp and a second person, most people can load and strap one in under half an hour.

Weight is the reason. A typical 50cc moped or scooter is in the low hundreds of pounds, much lighter than a motorcycle, and it rolls on its own wheels. You don't need a forklift or a crew. What you do need is a way up into the vehicle that isn't lifting it by hand, and a plan for keeping it upright once it's in.

Where it gets harder: larger scooters (150cc and up) get heavier fast, and a maxi-scooter is closer to a small motorcycle. Old mopeds with flat tires or seized brakes don't roll, so you're dragging dead weight up a ramp. And one person alone on a ramp with a moped is how mirrors, levers and shins get broken. Bring a helper.

My rule: same town, you have a pickup or trailer and a ramp? Do it yourself. Across the country, or no vehicle that fits? Ship it or hire a carrier.

Tools and equipment you need to move a moped

The essential equipment for moving a moped is a loading ramp, a wheel chock, four ratchet or cam straps and two soft loops. Here's the full list:

  • Loading ramp: a single motorcycle ramp or a folding ramp rated well above the moped's weight, long enough for a gentle angle.
  • Wheel chock: a front-wheel chock bolted or strapped to the bed or trailer, so the moped stands on its own while you strap it.
  • Four tie-down straps: ratchet straps or cam buckle straps rated for motorcycles.
  • Two soft loops: fabric loops that go around the handlebar or fork so metal hooks never touch paint or plastic.
  • Moving blankets or foam to pad the body panels and anything they could rub against.
  • Basic tools: a screwdriver and wrenches to pull mirrors, a windscreen or a top box.
  • Tire pump to get tires to proper pressure so it rolls and holds steady.
  • Work gloves for both people.

Skip the bungee cords. They stretch, they let the moped rock, and a rocking moped works itself loose on the first big bump.

Gear to move a moped: wheel chock, ratchet straps, soft loops, moving blanket, tire pump, wrench and removed mirrors

Does a moped need to be taken apart to move it?

A moped doesn't need to be taken apart to move it. The engine, wheels and body stay put; the only things worth removing are the parts that stick out or can fall off.

Here's what I'd take off or secure before loading:

  • Mirrors: two minutes with a wrench, and they're the first thing to snap on a ramp or against a truck wall.
  • Top box or rear rack case: remove it and carry it separately.
  • Tall windscreen: remove it if it would hit the truck roof, tailgate or a trailer rail.
  • Loose items: empty the under-seat storage and any baskets.

For fuel, low is better. A nearly empty tank weighs less and leaks less if anything tips, and if your moped has a fuel valve, turn it off. Professional carriers often ask for a low fuel level, so check with yours. For a long trip or shipping, disconnecting the battery prevents drain and accidental starts.

The one case where taking it further apart makes sense is a non-running project moped that has to fit in a car or small van. Then the front wheel or body panels may come off. That's a restoration-level job, so photograph and bag everything.

How to move a moped in 7 steps

Loading and tying down a moped follows the same sequence every time. Here's the order I'd follow.

  1. Prep the moped. Inflate tires, pull mirrors and the top box, lower the fuel level, and turn off the fuel valve if it has one.
  2. Set the chock and ramp. Mount the wheel chock at the front of the bed or trailer, centered. Hook the ramp securely to the tailgate or trailer edge on level ground.
  3. Walk it up the ramp. With the engine off, one person pushes from the side holding the handlebars and front brake, the other pushes from behind. Go in one steady motion and use the brake to stop, never your body.
  4. Seat the front wheel in the chock. The chock holds it upright while you work.
  5. Front straps first. Put the soft loops around the handlebar near the risers or the lower fork, hook a strap into each loop, and run them forward and outward to the anchor points at about a 45-degree angle. Tighten both evenly until the front suspension compresses partway.
  6. Rear straps. Run two more straps from solid rear frame points or the passenger grab rail (only if it's bolted to the frame) back and outward to anchors. These stop side-to-side and backward movement.
  7. Shake test. Push the moped hard side to side. It should move with the vehicle, not on its own. Tie off the strap tails so they don't flap, then recheck tension after the first few miles.
White moped standing in a wheel chock in a pickup bed, held by four ratchet straps on a moving blanket

How to protect the moped and your vehicle

Protecting a moped in transport comes down to keeping straps off plastic and keeping the bike from rocking. Most moped damage I see from DIY moves is cracked body panels where a strap pulled across them, and scratched paint from metal hooks.

Never anchor a strap to a body panel, mirror mount, turn signal, or a plastic luggage rack. Those parts aren't structural. Anchor to the handlebar (with a soft loop), the fork, or a frame member. If a strap has to pass over a panel, slide a folded blanket between the two.

Don't over-tighten either. You want the suspension compressed partway, not bottomed out. Bottoming the suspension for hours stresses the fork seals and can let the straps go slack the first time the bike settles.

For your vehicle, put a blanket or rubber mat under the stand area in a pickup bed so the moped doesn't scrape it, and pad the inside of the tailgate. In a van, protect the side walls where the bars might swing.

And use the stand only for parking. In transit, the chock and straps hold the bike. A side stand under load in a moving truck can bend or punch through a bed liner.

Moped on a utility trailer with soft loops on the handlebars and straps angled out to the rails, clear of the body panels

What does it cost to ship or professionally move a moped?

Shipping a moped usually costs less per mile on long trips than on short ones. uShip reports average moped shipping around $0.51 per mile for trips under 1,000 miles and about $2.30 per mile for trips under 100 miles, because short hauls still carry a fixed minimum to get a truck to you.

OptionBest forWhat drives the cost
DIY in your pickup or vanSame-town or nearby movesRamp, chock and straps (often borrowed or bought once)
Rented utility or motorcycle trailerLonger drives with a hitch-equipped carTrailer rental plus gas
Rental truck with a rampMoving a moped with the rest of a householdTruck rental and mileage
Motorcycle or moped carrier (uShip average)Long distance or no suitable vehicleAbout $0.51/mile under 1,000 miles; about $2.30/mile under 100 miles

Motorcycle shipping guides generally put rates between about $0.50 and $1.00 per mile for most trips, with heavier bikes and enclosed transport costing more. A moped is on the light end, so it usually sits toward the bottom of that range.

Before you book a carrier, ask whether the quote is open or enclosed transport, whether they need the fuel low and the battery disconnected, and how damage claims work. Take dated photos of the moped from all sides before it leaves.

After the move: getting it back on the road

Once a moped is unloaded, walk it down the ramp with the front brake covered, the same way it went up, with one person on the bars and one on the back.

Then run through a quick check. Reinstall the mirrors and top box. Reconnect the battery if you pulled it. Turn the fuel valve back on and top up the tank. Check tire pressure, squeeze both brakes, and test the lights and horn before you ride it. If the moped sat for a while before the move, old fuel can cause hard starting, so plan on fresh gas.

If you're moving to a new state, registration and title rules for mopeds vary a lot by state, so check with the new state's motor vehicle agency before you ride on public roads.

And if it turns out you don't want to move it at all, that's a real option. When a moped sells on Commonplace, our team handles the pickup and delivery and the buyer checks it before paying. You can browse used mopeds for sale or see the process on how Commonplace works. For electric scooters and mobility scooters, my guide on how to move a scooter covers the differences.

FAQ: moving a moped

Can a moped fit in an SUV or minivan?

Sometimes. A small 50cc moped can fit in a minivan with the seats out, but you'll need a ramp, strong tie-down points and protection for the interior. In most SUVs it won't fit upright, and laying a gas moped on its side risks fuel and oil leaks.

Can you lay a moped down to transport it?

I wouldn't with a gas moped. Laying it down can leak fuel and oil and crack body panels. Transport it upright in a chock with four straps.

Do you need to drain the gas to move a moped?

Not fully for a DIY move, but a low tank is better, and turn the fuel valve off if it has one. Carriers often ask for a low fuel level, so check their requirements before shipping.

How many straps do you need for a moped?

Four. Two at the front pulling forward and outward from the handlebar or fork, and two at the rear pulling back and outward from the frame. Use soft loops so hooks don't touch the bike.

Is it cheaper to ship a moped or sell it and buy another?

For a long move with an older moped, shipping can cost a real share of what the moped is worth, so selling it locally and buying at the new place often wins. For a moped you love, or a collectible like a vintage Vespa (see my guide on selling a Vespa), ship it.

If you'd rather skip the ramp, sell your moped on Commonplace and our team handles the pickup. You can start any listing from our sell page.

And if you're shopping, browse used mopeds on Commonplace. We deliver it to you, and you check it before you pay.