Commonplace
Sell an itemMy account
Home/Blog/Pool tables/How to Move or Take Apart a Pool Table: Slate, 9 Steps, and Pro Costs
Pool tables

How to Move or Take Apart a Pool Table: Slate, 9 Steps, and Pro Costs

How to move a pool table: why slate tables come apart, the tools, a 9-step teardown, protecting the slate, and what pool table movers charge.

Commonplace
Research
November 20, 2026 · 14 min read
More guides →

Here's how to move a pool table the right way: take it apart. A slate pool table comes down into rails, pockets, felt, slate and frame, the slate travels flat in its pieces (usually three), and the whole thing gets re-leveled and re-felted at the new spot. Professional pool table movers usually charge a few hundred dollars for a local job; Thumbtack's national data puts the typical range at roughly $270 to $590, and other cost guides run higher for heavy slate, stairs and long distances.

I help people buy and sell big, heavy furniture for a living, and pool tables are a special kind of heavy. The slate alone can outweigh a refrigerator, and it cracks if you flex it. So this guide covers whether you can move one yourself, the tools, the step-by-step teardown, how to protect the slate and the house, what the pros charge, and how it goes back together. If the real goal is getting the table out of your house for good, my guide on how to sell a used pool table is the better read.

Can you move a pool table yourself?

Yes, you can move a pool table yourself if you're handy, have three or four strong helpers and take it fully apart. What you can't do is move a slate table in one piece.

A full-size slate pool table often weighs 500 to 1,000 pounds, and big or one-piece slate tables can weigh far more. Most of that is the slate bed. People try to slide the whole table on furniture sliders, or lift it by the rails with six friends, and the result is a cracked slate, a racked frame, or a rail bolt torn out of the wood. I'd rather you didn't learn that one firsthand.

My rule: if you've assembled furniture with a socket set and you're comfortable with a staple gun, the teardown is doable. The reinstall is the hard part. Getting a table level enough to play true and stretching new felt tight is skilled work, and a lot of DIY movers do the takedown themselves and hire a pool table technician just for the setup.

Non-slate tables (MDF or particleboard beds) are a different story. They're lighter and often move in one piece with a dolly, but they don't survive repeated disassembly well, so move them gently and as few times as possible.

Tools and equipment you need to move a pool table

The essential tools for moving a pool table are a socket set, a power drill with driver bits, a staple remover and furniture dollies for the slate. Here's the full kit:

  • Socket wrench set for the rail bolts under the table.
  • Cordless drill and driver bits (Phillips and flat) for slate screws and pocket screws.
  • Staple puller or flat screwdriver for the felt and pocket staples.
  • Furniture dollies (at least two) and a hand truck for the frame and legs.
  • Moving blankets, at least one per slate piece plus more for rails and legs.
  • Plywood sheet to carry slate on if the path is uneven.
  • Ratchet straps for the truck.
  • Zip bags and a marker to bag and label every bolt and screw.
  • Phone camera to photograph the table before and during teardown.
  • For reassembly: a machinist's level, shims, beeswax for the slate seams, and a new felt cloth if the old felt is glued down.

Take photos of everything before you touch it: the rail layout, which rail goes where, how the pockets attach. Rails are not interchangeable, and labeling them saves an hour later.

Tools to take apart a pool table: socket set, drill, staple puller, level, beeswax, bagged bolts and a detached rail

Does a pool table need to be taken apart to move it?

A slate pool table must be taken apart to move it, full stop. A non-slate table can sometimes move whole, but a slate table moved assembled risks cracking the slate and damaging the frame.

The reason is how the table is built. The slate sits on the frame, usually in three pieces joined at seams that are filled and leveled during setup. The felt is stretched over it and stapled or glued to a wood backing on the slate. The rails bolt on through the slate from underneath. When you lift or tilt that assembly, the slate pieces and frame flex in different directions, and slate does not flex. It snaps.

Taking the table apart means each heavy part travels flat, supported and padded, and the frame travels empty. That's the whole idea.

How to move a pool table in 9 steps

Disassembling a pool table goes from the top down: pockets, rails, felt, slate, then the frame and legs. Here's the order I'd follow.

  1. Photograph and label. Take photos from every angle. Mark each rail with tape (head, foot, left, right) and note which pocket goes where.
  2. Remove the pockets. Pull the staples or unscrew the pocket brackets and set the pockets in a bag.
  3. Unbolt the rails. Crawl under the table and remove the rail bolts with a socket wrench, then lift the rails off as sections. Wrap each one in a blanket.
  4. Remove the felt. Pull the staples carefully if you want to reuse it. If the felt is glued to the slate, plan on new cloth; it rarely survives removal.
  5. Unscrew the slate. Find the screws that hold each slate piece to the frame and remove them. Scrape away the seam filler (beeswax or putty) so the pieces separate cleanly.
  6. Lift each slate piece with two to four people. Carry it flat or on edge with even support, never by a corner. Each piece of a three-piece set commonly weighs well over 100 pounds.
  7. Wrap the slate. Blanket each piece fully and tape the blankets closed. Never stack slate pieces directly on each other unpadded.
  8. Take down the frame and legs. Unbolt the legs and any cross beams. Bag the hardware and label it.
  9. Load and strap. Slate goes in first, on edge against the truck wall or flat on the floor, strapped so it can't slide or tip. Frame, rails and legs go in after.
Pool table with the felt removed to show the slate bed and its seams, with blanket-wrapped parts leaning on the wall

How to protect doors, floors and the slate itself

Protecting a pool table during a move is mostly about protecting the slate, because the slate is the only part you can't cheaply replace. A chipped corner or a hairline crack shows up as a roll the ball takes forever after.

Keep slate pieces fully supported at all times. Carry them on edge with people at both ends, or flat on a dolly with plywood under them. Don't let a piece rest on one corner, and don't lean it at a steep angle against a wall where it can slide.

For the house, slate on a dolly is a concentrated load. Lay hardboard or plywood over hardwood, pad door frames with blankets, and plan the stairs ahead. If the table is in a basement, measure the stairwell turn before moving day. I've written about getting big equipment in and out of a basement, and the same rules apply: measure first, more hands than you think, and slow on the turns.

Rails and legs are easier but still dent. Wrap every wood piece in its own blanket so they don't knock into each other in the truck.

What does it cost to have a pool table professionally moved?

A professional pool table move usually costs a few hundred dollars locally, with slate tables, stairs and long distances pushing it higher. Published averages vary by source, so here's how they line up:

SourceWhat it reports
Thumbtack (national data)Roughly $270 to $590 for a pool table moving service
HomeAdvisor (as reported in 2025 cost guides)National average around $650
Angi (2025, as cited by Lugg)$375 to $1,500 for a professional move, mostly disassembly, transport and re-leveling
Long-distance moves (industry guides)Roughly $600 to $4,000

Treat those as rough ranges. What moves your quote: slate versus non-slate, one-piece slate, stairs, whether new felt is included, and the distance. A full professional job typically takes a few hours, with most of the time spent on reassembly and leveling.

Ask any pool table mover three questions. Does the price include disassembly, transport, reassembly and leveling? Is new felt included or extra? Do they guarantee the level? A specialist will answer all three in one breath. A general mover usually won't.

Pool table slate pieces wrapped in moving blankets and strapped upright in a box truck beside the wrapped legs and rails

Putting a pool table back together

Reassembling a pool table is the reverse of the teardown, with one hard step in the middle: leveling the slate. Set the frame and legs first and level the frame. Then lay the slate pieces, align the seams, and shim until the whole bed reads level across both directions with a machinist's level.

Fill the seams with beeswax or the filler the table's maker recommends, scrape it flush, and screw the slate down. Stretch and staple (or glue) the bed felt, working from the center out. Then bolt the rails back on, felt them, and reattach the pockets. Roll a few balls down every direction before calling it done.

If that sounds like a lot, it is. This is the part I'd pay someone for even on a DIY move. A pool table that's slightly off level is a pool table nobody enjoys playing.

Is it worth moving, or should you sell?

Moving a pool table is worth it if you love the table and the new house has the room. A table needs roughly five feet of clear space around it for full cue strokes, so measure the new room before you pay to move it.

If the table doesn't fit the new place, or the move costs close to what the table is worth, selling it makes more sense. When a pool table sells on Commonplace, the buyer arranges the move through us, our team handles the pickup, and the buyer checks it on delivery before paying. You can see how that works on how Commonplace works, and browse used pool tables for sale to get a feel for what similar tables list for. I've also got a guide on how to move a piano if the pool table isn't the only heavy thing leaving the house.

FAQ: moving a pool table

How many people does it take to move a pool table?

Plan on four people for a slate table: two to carry each slate piece, plus help with rails and the frame. A non-slate table can often be handled by two or three people on dollies.

Can you move a pool table without taking it apart?

Only a non-slate table, and only a short distance on one floor. A slate table moved in one piece risks cracking the slate and damaging the frame, so take it apart.

Do you need new felt after moving a pool table?

Often, yes. Stapled felt can sometimes be reused if it's pulled carefully, but glued felt usually tears on removal. Budget for new cloth just in case.

How long does it take to move a pool table?

A professional crew typically takes a few hours for the full job, and reassembly with leveling takes the most time. A first-time DIY crew should plan on most of a day.

Is it worth moving an old pool table?

It's worth it for a quality slate table that fits the new room. For a cheaper non-slate table, a move can cost more than the table, and selling it and buying another at the new place is usually smarter.

If you'd rather skip the teardown entirely, list it. Sell your pool table on Commonplace and our team handles the pickup. You can start any listing from our sell page.

And if you're shopping, browse inspected used pool tables on Commonplace. We deliver, and you check it before you pay.